The product is not suitable for use on polished surfaces.

CHARACTERISTICS AND BENEFITS

•  Strong colour-enhancing capacity
•  Penetrates deep inside the material
•  Leaves surfaces stainproof
•  Provides hydro-repellency to the surface
•  Provides oleo-repellency to the surface
•  Brings out the characteristic veining on the surface
•  Ultra-resistant
•  Excellent water- and oil-repellent characteristics
•  Resistant to UV rays
•  Will not yellow over time
•  Adds a matt finish
•  Will not create a surface film
•  Also suitable for application outdoors.
•  Ideal for application on wet areas (sauna, shower, washbasins, fountains)

This product can be used on both indoor and outdoor surfaces.
Suitable for use on: Cement-marble agglomerate, Marble-resin agglomerate, Quartz-resin
agglomerate, Slate, Sandstone, Basaltina – Lava rock, Molten basalt, Cementina, Concrete,
Cotto, Granite, Limestone, Marble, Reconstituted (eco) stone, Porphyry, Quarzite, Terracotta,
Travertine, and Tuff.

15/20 m2/l

Brush, lambswool applicator, roller

Preparing and cleaning the surface

1. Carefully clean the surface, making sure to remove any dust or dirt present.

2. Never apply WET LOOK ECO to wet or damp surfaces.

3. Apply WET LOOK ECO to surfaces with a temperature of between +5 and +40°C

4. Any adjacent surfaces not being treated with the product must be protected.

Application 

5. Apply an even, abundant coat of product to a clean, dry surface with the preferred tool,
making sure to create an even layer to cover the whole surface being treated.

6. About 5-10 minutes after application, and in any case, before the product is completely
absorbed, as in cases of more absorbent surfaces, proceed to re-distribute the excess product
using the same tool used for application, taking care to achieve even coverage at the end of
treatment.

7. If the treatment is applied to more absorbent material, where the product is totally absorbed
without leaving residues, it is possible to apply a second coat of material, using the same
methods, about 2-3 hours later.

8. If the treatment has been applied to more compact and therefore, less absorbent materials,
where the product is not completely absorbed, even following redistribution, and therefore,
leaving surface residues, it is necessary to proceed to remove all residues thoroughly in order to
prevent subsequent problems of grease.

This operation is performed about 20-30 minutes after applying the product by brushing the
surface, dry, using a standard floor polisher (1.5 HP, 175 rpm) with white or lambswool disc or
wool-cotton attachment.

Alternatively, on tops, upright surfaces or small areas, residues can be removed with an orbital
or manual wheel, using a white disc or pad, or a compact felt or wool-cotton cloth.

To maximise the effectiveness of the stain-proofing treatment, the intensity of the colour enhancer and the durability of the treatment, it is possible to wait over 20-30 minutes, up to a
maximum of 45-60 minutes, before removing residues, to allow the product to penetrate fully
and deep down inside the structure of more compact materials. This way, the surface residues
may be slightly harder to remove.

Drying time

The product is fast drying and in any case, dries within 1-2 hours from application.

Opening to floor traffic

The surface can be opened to floor traffic about 4-6 hours after the product has been applied.

Complementary Cleaning and Maintenace Products

– For routine cleaning of a surface treated with WET LOOK ECO, we recommend: NEUGEL or
ALGAFLOOR

– For routine cleaning of a surface treated with WET LOOK ECO, we recommend: FABER 30 or
DETERFUG, according to the type of material.

– For de-waxing surface treated with WET LOOK ECO we recommend: DEC 21 and/or DECERA P