The product is not suitable for use on polished surfaces.

CHARACTERISTICS AND BENEFITS

•  Water-based product
•  Leaves the surface with excellent non-slip characteristics
•  Quick and easy application
•  Direct chemical action on the surface of the material
•  Will not create a film or leave residues
•  Extremely long-lasting treatment
•  No regular maintenance required

This product can be used on both indoor and outdoor surfaces.
Suitable for use on: Quartz-resin agglomerate, molten basalt, glazed ceramics, clinker, granite,
polished porcelain stoneware, natural porcelain stoneware, and textured porcelain stoneware.

10/20 m2/l

Brush, lambswool applicator, roller, airless

Preparing and cleaning the surface

1. Carefully clean the surface, making sure to remove any dust or dirt present.

2. Never apply YS ONE to wet or damp surfaces. The product must be applied to surfaces that
are as dry as possible.

3. Apply YS during the coolest periods of the day.

4. Do not treat with YS ONE if the flooring is exposed to direct sunlight.

5. Apply YS ONE to surfaces with a temperature of between +5 and +40°C

6. Any adjacent surfaces not being treated with the product must be protected.

7. Remove all pre-existing treatments – e.g., wax, resin, etc., etc. – from the surface to be
treated. To get the most from this treatment, it is important for YS ONE to enter into direct
contact with the surface of the material to be made non slip.

Application 

Considering the vast variety of materials that may require non-slop treatment, and which are all
different in terms of composition, resistance and surface hardness, to get the maximum results
in terms of non-slip quality, without changing the original appearance of the material, it is
necessary to carry out a preliminary test to identify the best possible contact time between the
surface and YS ONE. The test is carried out before proceeding to apply the treatment over the
whole surface, on a piece of material that has not been laid, or which is located in a concealed
area.

In general, the best time intervals can be summed up as follows:

– Ceramic and Stoneware: between 10 and 40 minutes

– Clinker and quartz-based agglomerates: between 30 and 60 minutes

– Granites: between 60 and 90 minutes

These times are based on our widest level of technical and operating experience; however, they
are purely a guideline and must only be used as a reference time when performing the
preliminary test.

The non-slip quality achieved during the preliminary test must be assessed after a thorough
rinse with plenty of water at the end of product application, to prevent any residues from giving
an incorrect idea of the result.

The assessment of the results must follow these simple but essential indications:

– Assess the test area in wet floor conditions

– Manually assess the surface of the floor with the fingertips, pressing down firmly in
order to simulate the weight of a person walking.

– Compare the treated area with an untreated area to get a good idea of the different
amount of grip generated.

8. The product is for use without dilution. Apply an even, abundant coat of product with the
preferred tool, making sure to create an even layer to cover the whole surface being treated

9. Leave the product for the amount of time identified in the preliminary test. During this
timeframe, it is important for the surface of the floor to be evenly wetted and covered with a
layer of product. Therefore, redistribute YS ONE as needed, applying more if necessary. The
presence of areas not covered by product during treatment may cause a final appearance or an
uneven non-slip surface.

10. After the time period identified in the test, remove all excesses, possibly using a liquid
vacuum cleaner and then rinse immediately after with plenty of clean water.
Removal of residues and rinsing with clean water is an operation that needs to be carried out
with care, considering the actual contact time between the product and the surface. Therefore,
begin to remove the product in the point where application of YS ONE was commenced, taking
care to remove it from the treated area in the same amount of time used to apply it. This will
allow the product to act for the same amount of time over the whole surface.

In order to make the whole treatment application stage easier, it is advisable to proceed in
single areas when the total area to be treated is very large. The areas must be divided according
to the established contact time. Brief contact times will require small areas to be treated. In
case of longer contact times, it is possible to divide into larger areas.

Drying time

Surfaces treated with YS ONE are dry once the water used for rinsing is dry.

Opening to floor traffic

Surfaces treated with YS-ONE can be opened to floor traffic once the product has been
completely removed.

Complementary Cleaning and Maintenace Products

– For routine cleaning of a surface treated with YS ONE, we recommend: ALGAFLOOR or NEUGEL
based on the type of material

– For extraordinary cleaning and for preliminary removal of wax for a surface treated with YS
ONE, we recommend: FABER 30 or DETERFUG, according to the type of material.